Home > Windows 7 > Change Motherboard Without Reinstalling Windows 7

Change Motherboard Without Reinstalling Windows 7

Contents

Can you elaborate on Step 5? I found this article while dealing with this issue and thought I'd share the solution I eventually worked out.PROBLEM: You have a pre-installed system running on a controller that is not Somewhere I have some 110 KB single-sided 5.25" floppies, too. It is empty and the working drive is disconnected. http://standardtechnological.com/windows-7/915-motherboard-driver-for-windows-7.html

Once started up and at the desktop, go into Device Manager.38. To select a third-party controller during Setup: 1) Obtain the correct driver file from the motherboard or controller card maker. The most amazing thing is I remember when you could store an entire application and data on one of those 110 KB floppies to run prior to introduction of hard drives. Great post....Thanks...:) 3degreeMay 17, 2011, 8:23 PM trajan said: Keeping in mind that the original poster wrote this back in 2006, there is a much (much) easier way now if you see here

Change Motherboard Without Reinstalling Windows 7

All I have available to me is the Recovery Console. Restart the system and start up the DOS-mode partition copy utility that you have, either from CD or floppy.31. This is caused by the presence of a mass storage controller on the new board that is incompatible with that on the previous motherboard. asumeing XP workable when it was 1st installed on you PC ...

  • Can someone point me to a guide that helps you with this, because for the life of me I can't find one.I am moving from an ICH7R to an ICH10R and
  • At one of the prompts, I selected "Load Third Party Drivers" and then used the flash drive to add them in.
  • Media center rules.
  • and these values * "DisplayName" type=REG_SZ data= .
  • Seshiru said: Has anyone who has replied to this thread so far actually read my first post?

The machine hard hangs. None of it worked. Some registry keys are created? New Motherboard Windows 10 Won't Boot How to recover from a corrupted registry that prevents Windows XP from starting http://support.microsoft.com/?scid=kb;en-us;307545Click to expand...

I went to the Asus site and downloaded the RAID driver package. Plus I hate Dell. Ask ! http://www.tomshardware.com/forum/196922-32-switching-storage-controllers-reinstalling-windows On reboot, Win2k will load the standard default IDE driver and should startup.

What messages do you get at that point? New Motherboard Startup Repair You will need: Your motherboard drivers. Norton Ghost was used as the partition copy utility.ReferencesMy primary impetus for trying and deveoping this procedure is a Microsoft support KB article entitled Stop 0x0000007B error after moving the Windows Neither of these options work!

How To Repair Windows 7 After Changing Motherboard

Double click it to make sure Windows says that the device is working properly.12. original site Backup all important data. Change Motherboard Without Reinstalling Windows 7 Join the community here, it only takes a minute. Paragon Adaptive Restore 2010 The archive program “7-Zip” available from http://www.7-zip.org/ installed.

Also, more detail about the original hardware and the VM setup might help diagnostics - CPU spec(s)? news more stack exchange communities company blog Stack Exchange Inbox Reputation and Badges sign up log in tour help Tour Start here for a quick overview of the site Help Center Detailed For Norton Ghost, you need to create a Ghost boot floppy. With the command listsvc you can enumerate all the drivers and services which are loaded on startup. New Motherboard Windows 7 Won't Boot

I was able to figure out a much simpler method of doing this. Make sure you're installing the correct driver. You may also... http://standardtechnological.com/windows-7/windows-xp-driver-on-windows-7.html I know that there are tools for this, but they either cost a lot or have extreme requirements.

Seshiru, Jan 23, 2005 #13 PangingJr Member Joined: Mar 14, 2003 Messages: 5,989 Likes Received: 56 Trophy Points: 0 atapi.sys - IDE/ATAPI Port Driver(Microsoft Corporation) intelide.sys - Intel PCI IDE Driver Msi Motherboard Driver Downloads If you delete it, you are forced to reboot and will have to start over. Use the RAID configuration utility (reboot if necessary) to configure the RAID1 on the two SATA drives.

Style Default Style Contact Us Help Home Top RSS Terms and Rules Forum software by XenForo™ ©2010-2016 XenForo Ltd. © Heaven Media Ltd.

I will be thankfull to you if you have any solution. Facebook Twitter YouTube Instagram Hardware Unboxed Google+ Subscribe to TechSpot RSS Get our weekly newsletter Search TechSpot Trending Hardware The Web Culture Mobile Gaming Apple Microsoft Google Reviews Graphics Laptops Smartphones This thread is intended for comments on the FAQ, not for solving problems. Install Drivers From Command Prompt PangingJr, Jan 23, 2005 #12 Seshiru New Member Joined: Jul 30, 2004 Messages: 11 Likes Received: 0 Trophy Points: 0 Ctrl-Alt-Del said: by using the Add/Remove...

After the restart, check Windows device manager, make sure your new disk controller appears in the device list (under IDE ATA/ATAPI Controllers if it's an IDE/SATA device, or under SCSI and This helped me out, big time. The usual result is boot cycling or a STOP 0x7BI have tried multiple methods to accomplish this including what is written at this site. check my blog Can I get all my data from these software?

SomeJoe7777Aug 27, 2006, 12:49 AM I performed this procedure again this weekend, successfully completing a task that I had set out to do in the first place.I originally had the following At the DOS prompt, type “DEVMGMT.MSC” and press Enter. This is a non-destructive system replacment where all your data and programs remain intact but the system is replaced from the install disk from scratch. Seshiru, Jan 22, 2005 #4 md5 New Member Joined: Dec 9, 2004 Messages: 854 Likes Received: 2 Trophy Points: 0 try repairing your installation via the XP CD md5, Jan

The recovery console will be started and you will be promped for the input of the windows which you want to repair. Log in with Facebook Log in with Twitter Log in with Google Your name or email address: Do you already have an account? Join thousands of tech enthusiasts and participate. It is still possible to boot Windows 2000 on the previous motherboard.

I do not want to use automatic physical to virtual conversion tools (don't ask why) I just want to preload necassary drivers with the help of recovery console or ERD commander Save changes in the BIOS if necessary, and restart the system.7. Boot to the BIOS and set the SATA controller to ATA. Windows start booting but then crashes with error "0x0000007b" So I want to load drivers of virtual SCSI controller with help of Windows recovery console or ERD commander or other utilities.

Enter your BIOS and set the boot disk to your CD/DVD drive. I can boot to a PE disk and verify that the file system is intact, but I think the hard disk drivers for Windows are wrong. You may be getting "Bootmanager not found" errors or similar.SOLUTION: You need to install the RAID drivers in your system. it works....

This is what I decided to test.Some other Microsoft KB articles that deal with this, and other related issues are:Moving a Windows Installation to Different HardwareHow to troubleshoot "Stop 0x0000007B" errors Shut down the system (power off).25. Once the clone is finished, shutdown and disconnect the working drive. I backed up my data on it and restored it (after lots of fun) to the ICH7R raid, but now I get the dreaded 7B BSOD.I can't boot the machine with