Home > Cd Rom > Cd Rom Driver In Config.sys

Cd Rom Driver In Config.sys

Also available in French. Risk Factor: 1 (Very low). Necessary for the next line and for Windows 9x and Smartdrive (line 19). Loads DOSKey, which enables fast recalling and editing of the command line at the DOS prompt.

Loading... Below is a listing of the major disc drive manufacturers and their related driver files. If no number is stated for the codepage, then the system codepage is set to 850 by default (for country 45), even though for instance codepage 865 is chosen in line the character set that is used for sorting and conversion to and from capital letters. click resources

If the number is smaller then some programs and batch-files might not run. /P indicates that the command interpreter shall stay resident and that AUTOEXEC.BAT shall be executed. /P may NOT Interface method´s annotations are inherited in Java 7 but not in Java 8 Understanding the definition of polynomially CPA (IND-CPA) security more hot questions question feed about us tour help blog MAP:G makes sure that both basic MIDI and extended MIDI can be played in DOS. For example: /P:T-M shows the CD512E connected to the TERTIARY port as a MASTER to use CD512E in MS-DOS mode, edit the DOSSTART.BAT file located in Windows directory and add

You can do this the easy way or the hard way: Using an Editor: Create an empty file using your editor, and then save it as "CONFIG.SYS". click Start, choose Shut Down, the shut down window will appear click the "Restart the Computer in the MS-DOS Mode" and modify the autoexec.bat and the config.sys files using the parameters The drivers from Microsoft and IBM uses a lot of memory - try to get another driver if you have one provided by Microsoft or IBM. Then it is not likely that any more Upper Memory can be gained using EMM386 It is possible that the computer works alright in DOS, but that Windows 9x cannot start

I have added the following lines to the CONFIG.SYS and AUTOEXEC.BAT files, respectively: DEVICE=D:\CDROM\CDROM.SYS /D:MSCD001 /V and C:\DRDOS\MSCDEX.EXE /D:MSCD001 /L:F The former loads the driver into memory, and the latter configures Loads the driver for Windows 9x's 32-bit file access. Thereafter COMMAND.COM will be loaded where there is free memory - in this instance into UMB 2. http://www.computerhope.com/cdromd.htm If you still encounter problems, attach to the other IDE port if your motherboard has one, or look on your favorite auction site for an ISA IDE adapter and see if

Loads the DOS XMS manager. version 6.22) to older DOS-programs, if they demand to be executed under a definite DOS version. Kozierok.All Rights Reserved. You need it only for installing DOS, Windows 3.x, or for setting up a new Windows 95/NT system that doesn't already have Windows installed.

A remark tells the computer to skip the line as the computer is booting and if is placed front of your CD-ROM lines it will cause the CD-ROM to not work.

Loads the driver for Windows 3.11's 32-bit file access. If instead the F8 key (plus 4 in Windows 9x) is pressed, then the lines in CONFIG.SYS and AUTOEXEC.BAT will be executed one line at a time. You need to copy it over before you start.

LH /L:0;2 /S C:\DOS\SMARTDRV 2048 128 /V C:\DOS\MODE CON RATE=32 DELAY=2 C:\DOS\MODE CON CP PREP=((865 850) C:\DOS\EGA.CPI) C:\DOS\MODE CON CP SEL=865 LH /L:2 C:\DOS\KEYB DK,865,C:\DOS\KEYBOARD.SYS ECHO. Change it now, and Windows will keep the change and things will work much better. More commands for use in CONFIG.SYS and AUTOEXEC.BAT can be seen in the chapter: MS-DOS 6.22 (Windows 3.11). shall be loaded.

  • The startup disk does not contain the CD-ROM driver or Mscdex.exe file.
  • Loads DOSKey, which enables fast recalling and editing of the command line at the DOS prompt.
  • Loads national language support, which makes it possible to change the codepage with the command: CHCP.
  • Within your config.sys, add LASTDRIVE=Z before the CD-ROM driver line.
  • This answer is useless.
  • are loaded.
  • In addition, if you boot from a floppy disk, the CD-ROM and MSCDEX drivers will not load unless you manually configure the Config.sys and Autoexec.bat files on the floppy disk to
  • Therefore I hereby pass on some advice about that subject.
  • Additional information See our CD-ROM and driver definitions for further information and related links on these terms.
  • Some CD-ROM driver install programs are totally brain-dead.

The setup also shows how to make a startup menu with two configurations - one for running with QEMM386, which starts by default after 2 seconds, and one for running with Loads the DOS XMS manager. Indicates how MIDI-files has to be played. Reboot: Remove the driver floppy disk from the floppy drive and reboot the system.

If your CD-ROM drive is supported in protected mode in Windows, the real-mode CD-ROM and MSCDEX drivers are most likely not being loaded in the Config.sys and Autoexec.bat or Dosstart.bat files An unbroken Upper Memory area is among other depending on the computers BIOS, the installed videocard and other plug-in cards installed in the computer. Add to Want to watch this again later?

Confix.sys can also be useful, allowing you to echo messages and pause bootup during config.sys processing.

MS-DOS 7.00 / 7.10 (Windows 95 & 98). The Lines with * can be omitted. Can be omitted. Show more Language: English Content location: United States Restricted Mode: Off History Help Loading...

Your system dates from the era when there were often issues with slaving two devices on a single IDE port that weren't from the same manufacturer and didn't explicitly support it. Because of the smaller clustersize used by FAT32, there is no longer the same need for harddisk partitioning in order of reducing the amount of wasted disk space. Below is an example of a line used to load the NEC CD-ROM drive. Prepares Danish/Norwegian (865) and international (850) codepage (character set) for the screen.

Rating is available when the video has been rented. Hardware conflicts can cause symptoms like what you describe: where the second time the computer boots then things don't initialize as desired. DOSSTART.BAT (Windows 95 & 98). Can be omitted.

Procedure Overview: Difficulty Level: 2-3 (Low to Moderate). Prepares Danish/Norwegian (865) codepage (character set) for the screen. Requires that a CD-ROM driver (line 13) with the same text after /D: is loaded. /M:15 states a suitable amount of buffers, and /E states that these buffer shall be loaded The average waste of space on a harddisk bigger than 1023 Mb will be 40% !!, while the waste on a harddisk between 512 and 1023 Mb will be 20%, and