Home > Cd Driver > Cd Driver Config.sys

Cd Driver Config.sys

Stacker disk compression. Selects Danish/Norwegian codepage (character set) for the screen. States in which directory temporary files can be placed by the applications (older programs). Loads the driver for the CD-ROM drive.

Loads the DOS EMS manager. If no number is stated for the codepage, then the system codepage is set to 850 by default (for country 45), even though for instance codepage 865 is chosen in line When Smartdrive is loaded AFTER MSCDEX (line 18), the cache will also work for the CD-ROM drive. Type "dir a:" and {Enter} to verify that the disk is readable. http://manmrk.net/tutorials/DOS/cdrom.htm

CONFIG.SYS * 1 2 3 4 5 6 7 8 9 10 11 * 12 13 14 15 16 NUMLOCK=OFF BREAK=ON DOS=HIGH,UMB FILES=40 FCBS=1,0 BUFFERS=10,0 LASTDRIVE=J STACKS=9,256 COUNTRY=045,865,C:\DOS\COUNTRY.SYS DEVICE=C:\DOS\HIMEM.SYS /V DEVICE=C:\DOS\EMM386.EXE Reports an earlier version of DOS (e.g. You may find the solution in this section of The Troubleshooting Expert. Autoexec.bat C:\WINDOWS\COMMAND\MSCDEX.EXE /D:NCI000 /V Config.sys DEVICE=C:\CDROM\IDE-CD.SYS /D:NCI000 If you need to be able to access the cd-rom drive in the DOS environment, press Start, select ShutDown, select "Restart the computer in

Therefore the same codepage should always be stated in line 9 and in line 22 to avoid problems with access to files with names, in which characters from the extended ASCII MS-DOS 7.00 / 7.10 (Windows 95 & 98) Windows 95 has DOS-version 7.00 Windows 95 OSR2 and Windows 98 has DOS-version 7.10 Under Windows 9x the following setup of CONFIG.SYS and version 6.22) to older DOS-programs, if they demand to be executed under a definite DOS version. Risk Factor: 1 (Very low).

Sets the last logical drive-letter to J: Sets stacks as Microsoft recommends it for Windows 3.11. If the Upper Memory in the address interval C800 to EFFF is unbroken, it should now, depending on the memory requirements for the CD-ROM and Mouse drivers, be possible to load Warning: Some people decide to wait until after installing Windows to change the drive letter; I don't recommend this because if you do, Windows will always try to look for its http://www.computerhope.com/cdromd.htm The order above provides the best utilization of the Upper Memory.

The problem with this is that if you later add another hard disk, that will take the letter your CD-ROM was using, and this can cause a lot of your CD-ROM-based In the example above, the last device: IFSHLP.SYS is loaded into UMB 1, and therefore FILES etc. Sets country to 45 (Denmark), with codepage 865 as the system character set i.e. Makes a little fun with the DOS prompt.

Furthermore the length of the PATH is limited by the size of the DOS environment (line 16). They'll just say "MSCDEX not found" and stop. "C:\DOS" is the traditional place for the MSCDEX.EXE file on older DOS 6.22 and earlier PCs. Guide to CONFIG.SYS & AUTOEXEC.BAT version 3.04 NOTE! Loads the DOS EMS manager.

This will create the AUTOEXEC.BAT file. If you get other errors you may have a problem with your drive or the particular disk you inserted. Do NOT delete these files, while Windows is running - some of them might be in use. the character set that is used for sorting and conversion to and from capital letters.

  • Sets buffers to 30.
  • If the Upper Memory in the address interval C800 to EFFF is unbroken, it should now, depending on the memory requirements for the CD-ROM and Mouse drivers, be possible to load
  • These systems can be identified by the words "Double Speed" or "Quad Speed" imprinted on the CD-ROM tray.
  • You need it only for installing DOS, Windows 3.x, or for setting up a new Windows 95/NT system that doesn't already have Windows installed.
  • Check System Files: Check your CONFIG.SYS and AUTOEXEC.BAT files by either editing them or displaying them to the screen using the command "type config.sys" or "type autoexec.bat".
  • This section in the Troubleshooting Guide explains what can happen.
  • Not responsible for any loss resulting from the use of this site.
  • States in which directory temporary files can be placed by the applications (older programs).
  • This setup also ensures access to CD-ROM drive and soundcard in MS-DOS mode.
  • Increases the typematic rate and delay for the keyboard.

If C:\DOS\COUNTRY.SYS is not stated, the country information file stated at COUNTRY= in CONFIG.SYS (line 9) is used. Indicates how MIDI-files has to be played. Also available in French. If it is EDIT.COM and the file is on the floppy, this command will do the job, issued from the C: root directory: "copy a:edit.com c:".

Loads the DOS CD-ROM extension for access to the CD-ROM drive. Requires that DISPLAY.SYS is loaded (line 13). States the name and location of the command interpreter. /E: states the size of the DOS environment. 1024 is suitable, as DOS 7.x automatically adds 1040 to the size which cannot

If the driver disk does not contain MSCDEX.EXE, you will need this file as well; it may be on your operating system boot disk, or Windows 95 startup disk.

Also look at the chapter: More Upper Memory with EMM386. The PATH line can not contain more then 127 characters. Then, tell the system to use this letter by editing AUTOEXEC.BAT and adding this parameter to the MSCDEX.EXE line: "/L:J" (change "J" to whatever letter you want to use). This frees up more conventional memory for your applications.

What is written after /D: must also be written after /D: in line 18. Before you begin to change the CONFIG.SYS and AUTOEXEC.BAT files, you should do the following: Format a floppy diskette with the command: FORMAT A: /U /S Save copies of the Before you begin ! So the line will now look something like "C:\MSCDEX /D:MSCD001 /L:J" (plus whatever other parameters were there before).

The order of the lines should not be altered. Alternative Memory Managers (QEMM386). If you haven't got a DOS CD-ROM driver, then you might use the SAMPLE.SYS driver located at the Windows 95 installation diskette. Then you edit the autoexec.bat file (in a DOS prompt on the root directory you type EDIT AUTOEXEC.BAT ) and add the line as shown below.

You of course replace this name on the config.sys entry with the one you find on your own CDROM folder. Your driver might have another name. The order of the lines should not be altered. Windows (or other operating system) CD-ROM.

Harddisk partitioning. This is done by making the following changes under [Options] in the file C:\MSDOS.SYS: to: BootGUI=1 Logo=1 BootGUI=0 Logo=0 MSDOS.SYS is a hidden read-only system file, why it is necessary the character set that is used for sorting and conversion to and from capital letters. Loads the DOS Smartdrive disk cache for faster reading and writing on the (hard)disks.

Windows 9x's 32-bit CD-ROM driver should be a little faster than a 16-bit DOS driver, but some programs cannot run with the 32-bit driver.